Do It Yourself Bathtub Installation.
Do It Yourself Bathtub Installation.
Blog Article
What are your opinions regarding A Step-by-Step Guide to Installing a Bathtub?
Mounting a tub isn't exactly brain surgery, however it does require strong plumbing, woodworking, and sometimes, tiling abilities. Replacing an old bathtub with a brand-new one is also a reasonably tough project. If the old bathtub is readily accessible, the job can move immediately; if you have to open up a wall surface to remove the old bathtub and place the new bathtub, the job is much harder. In either instance, the project is within a residence handyman's skills, although you will certainly need an assistant to leave the old tub as well as set in the brand-new one. Ensure you have actually qualified on your own for the task and also are comfortable trying it. Instead of hiring a specialist to take over a halfway-completed task, it is better to think about employing one prior to you begin. Possibilities are you might need a specialist plumber to make tube connections.
This article will certainly aid you set up a brand-new tub in your washroom if you have currently bought a new bathtub and do not require to alter the plan of your previous water supply pipes.
Your devices and material list ought to make up the following:
Getting ready for the Installment
To start with, the supporting framework supplied with the bathroom needs to be fitted (if required) according to the producer's directions. Next off, fit the faucets or mixer to the bath tub. When fitting the tap block, it is essential to ensure that if the tap includes a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is also sensible to fit a supporting plate under the taps system to avoid stress on the tub.
Fit the adaptable faucet adapters to the bottom of both faucets making use of 2 nuts and olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet through the hole in the bath. Use the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make certain you utilize every one of the supplied washers.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Link the bottom of the overflow tube in a similar manner.The bathroom need to currently prepare to be fitted in its final position.
Removing Old Touches
If you require to change old taps with new ones as a part of your installation, after that the first thing you need to do is separate the water system. After doing so, switch on the faucets to drain pipes any type of water remaining in the system. The process of getting rid of the existing faucets can be rather problematic due to the limited gain access to that is typically the case.
Make use of a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipes to the faucets. Have a towel prepared for the remaining water that will certainly originate from the pipes. Once the supply pipelines have been removed, make use of the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to quit the single faucets from transforming during this procedure. When the taps have actually been eliminated, the holes in the bath/basin will need to be cleaned up of any old securing compound.
Prior to carrying on to fit the new faucets, compare the pipeline links on the old faucets to the new taps. If the old faucets are longer than the new taps, after that a shank adapter is needed for the new faucets to fit.
Mounting the Tub
Using both wooden boards under its feet, place the bath tub in the needed setting. The wood boards are practical in uniformly spreading the weight of the bath tub over the area of the boards instead of concentrating all the weight onto four little points.
The following goal is to ensure that the bath tub is leveled all round. This can be accomplished by checking the level and readjusting the feet on the tub until the level reads degree.
To set up taps, fit all-time low of the furthest versatile tap adapter to the suitable supply pipeline by making a compression join; after that do the exact same for the other faucet.
Switch on the water and examine all joints as well as brand-new pipework for leaks and also tighten them if required. Load the tub as well as likewise examine the overflow outlet and also the normal electrical outlet for leakages.
Lastly, deal with the bath paneling as defined in the producer's user's manual. Tiling and securing around the tub should wait up until the bath tub has been utilized at the very least once as this will resolve it right into its final setting.
Suitable New Touches
If the tails of the new taps are plastic, after that you will certainly need a plastic port to prevent damages to the string. One end of the connector fits on the plastic tail of the faucet and also the other end supplies a connection to the existing supply pipelines.
If you need to fit a monobloc, then you will certainly call for decreasing couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next off, position the tap in the installing opening in the bath/basin guaranteeing that the washing machines remain in place between the faucet and also the sink. Secure the tap in position with the manufacturer offered backnut. When the faucet is firmly in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with typical faucet adapters. The former type must be attached to the faucet ends first, tightening just by hand. The supply pipelines can later on be connected to the other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Bath tub
In the location where the bath meets the tile, it is needed to secure the accompanies a silicone rubber caulking. This is necessary as the fitting can relocate sufficient to fracture a rigid seal, causing the water to penetrate the wall between the bathroom as well as the tiling, causing difficulties with wetness and also possible leaks to the ceiling below.
You can choose from a variety of coloured sealants to blend in your fixtures and fittings. They are sold in tubes and cartridges, and are capable of sealing gaps up to a width of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with twists of soaked newspaper or soft rope. Remember to constantly load the bath tub with water prior to securing, to permit the motion experienced when the bathtub remains in use. The sealant can break fairly early if you do not take into account this activity prior to securing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are additionally quickly offered on the market. It is advisable to fit the tiles making use of waterproof or water-proof adhesive and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I was shown that editorial on How to Install a Bathtub through a good friend on a different web property. Do you know another person who is curious about the topic? Why not promote it. Many thanks for your time. Kindly come by our site back soon.
Visit My Site Report this page